Getting the Heat Right: Sidel Matrix Infrared Lamps Here is the problem when you swap out OEM lamps in a Sidel Matrix or SIPA SFR 12: the temperature...

Fixing the Headache of Sidel SBO Lamp Failures If you’ve spent any time around SIG Blomax lines, you know the drill. A tube pops. The line...

Getting the Heat Right for Your Sidel Matrix SBO Series 2 If you’ve ever tried to swap out lamps in a Sidel SBO Series 2, you know that wattage...

Fixing the “Cold Spot” Headache in Sacmi SBF and Husky HyPET Lines If you’ve spent any time on the shop floor, you know the...

Tired of your SIG Blomax lamps burning out? There’s nothing more frustrating than a full production line grinding to a halt because a few preform...

Making SACMI PET Lamps Actually Work (Without the Headache) Look, if you’re running a high-speed PET blowing line, you know the drill. One lamp...

Getting Your SIG Blomax 4 Heating Back on Track When your infrared lamps start wearing out in a SIG Blomax 4, it’s easy to think of it as just...

Making Your PET Blow Molding Lamps Actually Work If you’re running Krones Contiform machines, you know the struggle. You need that preform to...

Getting Your Sidel Matrix Lamps Right When you’re looking for a replacement lamp for a Sidel Matrix system, don’t just chase a part...

Getting Your Krones Contiform Heat Profiles Just Right If you’re running a Krones Contiform or a KOSME KSB 4000/6000, you already know the...

Stop Waiting on Your Rotary Oven to Heat Up There is nothing more frustrating than watching your throughput tank because your rotary oven is taking...

Stop Wasting Preforms: Getting Your SACMI Heaters Up to Speed If you’re running a high-speed PET line, you know the oven is where the magic...

Getting Your SACMI and Krones S24 Lamps to Actually Keep Up If you’re running a SACMI or Krones S24, you know the rhythm. It’s fast....

Why Your Oven Still Leaves the Center Cold (And How We Fix It) Ever pulled a tray of food out of a commercial oven only to find the outside is...

If you’ve ever tried replacing heating lamps in a PET blow molding machine, you know the headache. Either the lamp doesn’t quite fit, or the...

A Better Way to Handle IR Lamps for Your SIG Blomax 4/6/8 Let’s be honest: when an infrared lamp pops on your SIG Blomax line, everything stops. It’s...

Getting the Most Out of Your Krones Contiform Heat Running a Krones Contiform line is always a bit of a balancing act. You want maximum heat, but you...

Getting Your SIPA Preform Heating Just Right Ever notice your SIPA rotary machines acting up with weird heating fluctuations? Usually, it comes down...

The Lamp That Gets Your KHS Blow Molding Back on Track Ever had one of those days where your KHS blow molding line just can’t get its act together?...

Introduction We built the Krones Contiform 3 infrared lamp to be a straight-up, drop-in replacement for high-speed rotary blow molding lines. It was...

Introduction We built the Alibaba SIPA SFR IR lamp for one reason: to keep pace with the Husky HyPET system. It’s all about giving you heat that’s...

In a busy kitchen, oven downtime is money left on the table. Waiting for a deck oven to come up to temp, or chasing hot and cold spots in a...

In a busy display case, the last thing you need is a heat source that torches the top while the bottom goes cold. Customers see uneven color, and you...

On the blow molding floor, a heating failure never picks a good moment. Preforms undershoot, and you’re making scrap. They overheat, and you get thin...

On the blow molding line, the oven is where the run either makes it or breaks it. Preforms that come out with a cool shoulder and a hot body make you...

On a Husky HyPET line, preform heating isn’t just another step. It’s the line in the sand between making cycle and getting throttled back by the...